Can You Strip 12 Point Sockets?

Are 12 point sockets bad?

A 12 point socket on a 6 point fastener is significantly more prone to fail.

There are a few 12 point fasteners in use but they are very rare and when it’s necessary to use a breaker bar in a confined area the 12 point can be necessary.

A DIYer would rarely need them though..

Are 12 point sockets better than 6 point?

Answer: It’s true that 12-point sockets are fine for most lightweight repairs, but heavy wrenching calls for a six-point socket. A six-point socket is much less likely to slip off a stubborn fastener or round over the corners.

What can I do with old sockets?

Re: What do you do with your old wrenches and sockets. Trade them for ones you don’t have in your keeper sets or throw them in a cheap garage sale box and sell them at your own garage sale.

What are 12 point bolts used for?

The twelve point head design is tightened with standard twelve point socket wrenches. The 12 point design permits greater torque to be applied to the bolt and eliminates the rounding of the hex socket that occurs with standard hex sockets.

Are 12 point sockets better?

The additional points make these sockets easier to connect with the heads of fasteners. This is ideal if you are trying to work on a fastener that is hard to see or you cannot see at all. 12 point sockets are also great for use in tight spaces as they allow you to connect to a fastener at more angles.

Can I use a 12 point socket on a 6 point nut?

This geometry will also fit on a 6-point fastener. Your tool will work best when it fits precisely onto the fastener. If your fastener is 12-point, which is somewhat uncommon, then you must use a 12-point tool. For 6-point fasteners, a 6-point tool is your best choice.

Will a 12 point socket work on a Torx bolt?

Neither a 6 or a 12 point socket will help when an E-Torx is required.

Is it OK to use impact sockets with a ratchet?

A hand ratchet will connect and drive an impact socket just as it would with a normal socket. Similarly, it is safe to use an impact socket on a hand ratchet (although not vice versa).

Why are impact sockets black?

Impact sockets are typically black. This is because the surface is carbonized in order for it to harden. Ensuring that the surface is hard allows the sockets to absorb sudden torque changes i.e. “impact” a lot better.

Why do impact sockets have a hole?

That hole has a very specific purpose. It’s called a retaining pin and it is integral in making sure an impact socket and impact gun/wrench work perfectly together. The pin prevents the socket from coming off the end of the wrench or gun as a result of vibrations.

What are 8 point sockets for?

An 8 point socket set is essential to.me, sometimes for pipe plugs that have been around too long, and sometimes working on old machinery where I may find square bolts, lags or nuts. … 8 Point sockets work great for removing square bolts and plugs.

Do I need a socket wrench?

About the only time you will use or need a socket set is if you are going to work on your vehicles. If you are only interested in doing basic repairs around your home, No you do not need a socket set. A good set of open end wrenches will suffice as well as a good Crescent type wrench.

Can a 12 point socket be used on a hex bolt?

A 12-point bolt design offers the same bearing surface as a hex head cap screw of comparable size. … It’s much better to use a 12-point bolt in this application. The 12-point is also a bit smaller than the flat of the hex; therefore, a smaller socket can be used to get down inside.

Do you really need deep sockets?

Deep sockets are better for specific jobs instead of general use. If you have bolted joints, they make a much better option for your socket wrench than shallow sockets. Because the length of the bolt means the nut will need to go further into the socket, deep sockets are a much better choice. …

Is Kobalt made by Snap on?

Also, are Kobalt Tools made by Snap on? The first is from Bob Payne of Cornwell Tool Distributor – He indicates that Kobalt is not made by Snap-On. … Many of the Kobalt ratchets, sockets, wrenches, and drive acessories were made by Danaher in the USA .